Develop Reference

Pic16F688 has no stable readings via buletooth

I have spent much time trying to find out where is my mistakes while Im flashing the PIC16F688. The Pic has successfully flashed using PicKit2. Im using the Pic to convert analog pressure sensor to digital output and sending the data via Bluetooth, but the Bluetooth is not receiving stable numbers of data. The data is consist of 4 character decimal number that is between 0 and 1023.
The problem is that the Bluetooth can't wait at specific number and keep reading it, instead, it is reading the 4 digits in random.
I think my mistake is within the configuration of internal oscillator.
I'm attaching my code, the code is written to configure the flexiforce sensor circuit that outputs analog voltage up to 5v, and then the pic duty is to convert it to digital as I mentioned above.
it might be my wiring is not correct, please If you could help out with this one
and what configuration "at edit project" do I need to choose for Mikro PRO software?
I used "Bluetooth terminal" app to see my data asynchronous from Bluetooth.
Thank you.
char *temp = "0000";
unsigned int adc_value;
char uart_rd; int i;
void main()
{
OSCCON = 0x77;
ANSEL = 0b00000100;
CMCON0 = 0X07;
TRISA = 0b00001100;
UART1_Init(9600);
Delay_ms(100);
while (1)
{
adc_value = ADC_Read(2);
temp[0] = adc_value/1000+48;
temp[1] = (adc_value/100)%10+48;
temp[2] = (adc_value/10)%10+48;
temp[3] = adc_value%10+48;
for (i=0;i<4; i++)
UART1_Write(temp[i]);
UART1_Write(13);
Delay_ms(1000);
}
}

You can use itoa function to convert ADC integer value to characters for sending over UART. If there is error in calculation then you wont get appropriate value. Below code snippet for your reference :
while (1)
{
adc_value = ADC_Read(2);
itoa(adc_value, temp, 10);
for (i=0;i<4; i++)
UART1_Write(temp[i]);
UART1_Write(13);
Delay_ms(1000);
}
Please check Baud Rate you have configured at both ends is same or not. If baudrate mismatches then you will get Random value at Bluetooth Terminal where you are reading values.

What i would suggest, if you have a logic analyser, hook it up. If you don't recalculate your oscillator speed with the datasheet. It could just be that the internal oscillator is not accurate enough. What also works, is to write a function in assembly that waits a known time (by copy-pasting a lot of NOPs and using this to blink a led. Then start a stopwatch and count, say, 100 blinks. This is what i used to do before i had a logic analyser. (They are quite cheep on ebay).

ConsumerIrManager.transmit broken in Lollipop?

I upgraded my Samsung Galaxy S4 from latest KitKat to Lollipop (5.0.1) yesterday and my IR remote control app that I have used for months stopped working.
Since I was using a late copy of KitKat ConsumerIrManager, the transmit( ) function was sending the number of pulses using the code below. It worked very nicely.
private void irSend(int freqHz, int[] pulseTrainInMicroS) {
int [] pulseCounts = new int [pulseTrainInMicroS.length];
for (int i=0; i<pulseTrainInMicroS.length; i++) {
long iValue = pulseTrainInMicroS[i] * freqHz / 1000000;
pulseCounts[i] = (int) iValue;
}
m_IRService.transmit(freqHz, pulseCounts);
}
when it stopped working yesterday, I began looking closely at it.
I noticed that the transmitted waveform is not having any relationship with the requested pulse train. even the code below doesn't work correctly! there is
private void TestSend() {
int [] pulseCounts = {100, 100, 100};
m_IRService.transmit(38000, pulseCounts);
}
the resulting waveforms had many problems and so are entirely useless.
the waveforms were entirely wrong
the frequency was wrong and the pulse spacing was not regular
they were not repeatable
looking at the demodulated waveform:
if my 100, 100, 100 were correctly rendered, I should have seen two pulses 2.6ms (before 4.4.3(?) 100 us) long. instead I received (see attached) "[demodulated] not repeatable 1.BMP" and "[demodulated] not repeatable 2.BMP". note that the waveform isn't 2 pulses...in fact, it's not even repeatable.
as for the captures below, the signal goes low when the IR is detected.
we should have seen two pulses going low for 2.6 ms and 2.6 ms between them (see green line below).
I had also tried shorter pulses using 50, 50, 50 and have observed that the first pulse isn't correct either (see below).
looking at the modulated waveform:
the frequency was not correct; instead, it was about 18kHz and irregular.
I'm quite experienced with this and have formal education in electronics.
It seems to me there's a bug in ConsumerIrManager.transmit( )...
curiously, the "WatchOn" application that comes with the phone still works.
thank you for any insights you can give.
Test equipment:
Tektronix TDS-2014B, 100 MHz, used in peak-detect mode.

As #IvanTellez says, a change was made in Android in respect to this functionality. Strangely, when I had it outputting simple IR signals (for troubleshooting purposes), the function behaves as shown above (erratically, wrong carrier frequency, etc). When I eventually returned to normal types of IR signals, it worked correctly.

Is logging Android systrace events directly from native code possible, without JNI?

The Android systrace logging system is fantastic, but it only works in the Java portion of the code, through Trace.beginSection() and Trace.endSection(). In a C/C++ NDK (native) portion of the code it can only be used through JNI, which is slow or unavailable in threads without a Java environment...
Is there any way of either adding events to the main systrace trace buffer, or even generating a separate log, from native C code?
This older question mentions atrace/ftrace as being the internal system Android's systrace uses. Can this be tapped into (easily)?
BONUS TWIST: Since tracing calls would often be in performance-critical sections, it should ideally be possible to run the calls after the actual event time. i.e. I for one would prefer to be able to specify the times to log, instead of the calls polling for it themselves. But that would just be icing on the cake.

Posting a follow-up answer with some code, based on fadden's pointers. Please read his/her answer first for the overview.
All it takes is writing properly formatted strings to /sys/kernel/debug/tracing/trace_marker, which can be opened without problems. Below is some very minimal code based on the cutils header and C file. I preferred to re-implement it instead of pulling in any dependencies, so if you care a lot about correctness check the rigorous implementation there, and/or add your own extra checks and error-handling.
This was tested to work on Android 4.4.2.
The trace file must first be opened, saving the file descriptor in an atrace_marker_fd global:
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#define ATRACE_MESSAGE_LEN 256
int atrace_marker_fd = -1;
void trace_init()
{
atrace_marker_fd = open("/sys/kernel/debug/tracing/trace_marker", O_WRONLY);
if (atrace_marker_fd == -1) { /* do error handling */ }
}
Normal 'nested' traces like the Java Trace.beginSection and Trace.endSection are obtained with:
inline void trace_begin(const char *name)
{
char buf[ATRACE_MESSAGE_LEN];
int len = snprintf(buf, ATRACE_MESSAGE_LEN, "B|%d|%s", getpid(), name);
write(atrace_marker_fd, buf, len);
}
inline void trace_end()
{
char c = 'E';
write(atrace_marker_fd, &c, 1);
}
Two more trace types are available, which are not accessible to Java as far as I know: trace counters and asynchronous traces.
Counters track the value of an integer and draw a little graph in the systrace HTML output. Very useful stuff:
inline void trace_counter(const char *name, const int value)
{
char buf[ATRACE_MESSAGE_LEN];
int len = snprintf(buf, ATRACE_MESSAGE_LEN, "C|%d|%s|%i", getpid(), name, value);
write(atrace_marker_fd, buf, len);
}
Asynchronous traces produce non-nested (i.e. simply overlapping) intervals. They show up as grey segments above the thin thread-state bar in the systrace HTML output. They take an extra 32-bit integer argument that "distinguishes simultaneous events". The same name and integer must be used when ending traces:
inline void trace_async_begin(const char *name, const int32_t cookie)
{
char buf[ATRACE_MESSAGE_LEN];
int len = snprintf(buf, ATRACE_MESSAGE_LEN, "S|%d|%s|%i", getpid(), name, cookie);
write(atrace_marker_fd, buf, len);
}
inline void trace_async_end(const char *name, const int32_t cookie)
{
char buf[ATRACE_MESSAGE_LEN];
int len = snprintf(buf, ATRACE_MESSAGE_LEN, "F|%d|%s|%i", getpid(), name, cookie);
write(atrace_marker_fd, buf, len);
}
Finally, there indeed seems to be no way of specifying times to log, short of recompiling Android, so this doesn't do anything for the "bonus twist".

I don't think it's exposed from the NDK.
If you look at the sources, you can see that the android.os.Trace class calls into native code to do the actual work. That code calls atrace_begin() and atrace_end(), which are declared in a header in the cutils library.
You may be able to use the atrace functions directly if you extract the headers from the full source tree and link against the internal libraries. However, you can see from the header that atrace_begin() is simply:
static inline void atrace_begin(uint64_t tag, const char* name)
{
if (CC_UNLIKELY(atrace_is_tag_enabled(tag))) {
char buf[ATRACE_MESSAGE_LENGTH];
size_t len;
len = snprintf(buf, ATRACE_MESSAGE_LENGTH, "B|%d|%s", getpid(), name);
write(atrace_marker_fd, buf, len);
}
}
Events are written directly to the trace file descriptor. (Note that the timestamp is not part of the event; that's added automatically.) You could do something similar in your code; see atrace_init_once() in the .c file to see how the file is opened.
Bear in mind that, unless atrace is published as part of the NDK, any code using it would be non-portable and likely to fail in past or future versions of Android. However, as systrace is a debugging tool and not something you'd actually want to ship enabled in an app, compatibility is probably not a concern.

For anybody googling this question in the future.
Native trace events are supported since API Level 23, check out the docs here https://developer.android.com/topic/performance/tracing/custom-events-native.

Regexp to match logcat brief format with g_regex_match_simple

I'm trying to write a wireshark dissector for logcat logs in various text formats.
To do it I need to detect which type of logcat I'm reading, and then get the respectable parts extracted. I thought that using a regular expression would do the trick, but apparently it doesn't.
Here is my regular expression:
[IVDWE]/.*\(\s*[0-9]*\):\s.*
As it should be Perl compatibile I tried it with Perl from command line and it seems to work. Yet when loading a line, ex.
I/bdAddrLoader( 184): option : f=/persist/bluetooth/.bdaddr
with g_regex_match_simple, the expression does not match from opening round brace. I tried escaping it with 1-4 \, but it didn't work.
Edit:
Turns out that I've tried \,'\`,and \\\\ versions, but missed somehow \\...

It works for me with two backslashes:
#include <glib.h>
int
main(int argc, char *argv[]) {
gboolean res = g_regex_match_simple ("[IVDWE]/.*\\(\\s*[0-9]*\\):\\s.*",
"I/bdAddrLoader( 184): option : f=/persist/bluetooth/.bdaddr",
0, 0);
g_message ("%s", res ? "true" : "false");
return 0;
}

Why does glGetIntegerv for GL_NUM_SHADER_BINARY_FORMATS generate GL_INVALID_ENUM?

I am using the official Android port of SDL 1.3, and using it to set up the GLES2 renderer. It works for most devices, but for one user, it is not working. Log output shows the following error:
error of type 0x500 glGetIntegerv
I looked up 0x500, and it refers to GL_INVALID_ENUM. I've tracked down where the problem occurs to the following code inside the SDL library: (the full source is quite large and I cut out logging and basic error-checking lines, so let me know if I haven't included enough information here)
glGetIntegerv( GL_NUM_SHADER_BINARY_FORMATS, &nFormats );
glGetBooleanv( GL_SHADER_COMPILER, &hasCompiler );
if( hasCompiler )
++nFormats;
rdata->shader_formats = (GLenum *) SDL_calloc( nFormats, sizeof( GLenum ) );
rdata->shader_format_count = nFormats;
glGetIntegerv( GL_SHADER_BINARY_FORMATS, (GLint *) rdata->shader_formats );
Immediately after the last line (the glGetIntegerv for GL_SHADER_BINARY_FORMATS), glGetError() returns GL_INVALID_ENUM.

The problem is the GL_ARB_ES2_compatibility extension is not properly supported on your system.
By GL_INVALID_ENUM it means that it does not know the GL_NUM_SHADER_BINARY_FORMATS and GL_SHADER_BINARY_FORMATS enums, which are a part of the said extension.
In contrast, GL_SHADER_COMPILER was recognized, which is strange.
You can try using GL_ARB_get_program_binary and using these two instead:
#define GL_NUM_PROGRAM_BINARY_FORMATS 0x87fe
#define GL_PROGRAM_BINARY_FORMATS 0x87ff
Note that these are different from:
#define GL_SHADER_BINARY_FORMATS 0x8df8
#define GL_NUM_SHADER_BINARY_FORMATS 0x8df9
But they should pretty much do the same.